SR15-D2A2 pyranometer

SR15 first class pyranometer
SR15 first class pyranometer
SR15 digital series first class pyranometer
SR15 first class pyranometer with tube levelling mount
Digital first class pyranometer with Modbus over TTL and 4-20 mA output

SR15 digital pyranometer series is an all-digital range of solar radiation sensors applied in general high-accuracy observations. SR15 pyranometers comply with the “first class” specifications according to the ISO 9060:1990 standard and “spectrally flat class B” requirements in the 2018 revision. Version SR15-D2A2 offers Modbus over TTL, and 4-20 mA current loop output.

Specifications
Measurand
  • hemispherical solar radiation
ISO 9060:2018 classification
  • class B (first class)
IEC 61724-1:2017 compliance
  • class C
Would you like a personalised quote?

or contact us: info@hukseflux.com

Specifications

Measurand
  • hemispherical solar radiation
Application
  • National Meteorological Networks
  • PV monitoring commercial and utility scale
  • PV monitoring small sized
  • meteorology / climatology
  • other
Heater
  • no
ISO 9060:2018 classification
  • class B (first class)
IEC 61724-1:2017 compliance
  • class C
Output
  • 4-20 mA current loop
  • Modbus TTL
Calibration uncertainty
  • < 1.8 % (k = 2)
Calibration traceability
  • to WRR
Spectral range
  • 285 to 3000 x 10⁻⁹ m
Response time
  • < 10 s
Zero offset a
  • 5 W/m² unventilated
Rated operating temperature range
  • -40 to +80 °C
Temperature response
  • < ± 2 % (-10 to +40 °C)
Heater
  • 1.5 W at 12 VDC
Standard cable length
  • 5 m
Levelling
  • optional spring-loaded levelling, with or without tube mount
Output
  • :
Communication protocol
  • Modbus over TTL
Transmission mode
  • RTU
Output
  • irradiance in W/m² and instrument body temperature in °C
On-board heater
  • not included
Analogue output
  • 4-20 mA current loop
Options
  • spring-loaded levelling; practical for easy mounting, levelling and instrument exchange on flat surfaces
  • tube levelling mount with set of bolts
  • PMF01 bracket for tilted installations
  • longer cable; 10 and 20 metres length
  • 20 metres extension cable with 2 connectors
Manuals & Downloads

Description

SR15 digital series first class pyranometer

Improved measurement accuracy

Calibration of SR15 pyranometer has been improved; our latest calibration method results in an uncertainty of the sensitivity of 1.8 %, compared to typical uncertainties of higher than 2.8 % for this pyranometer class. SR15’s response time is < 10 s, a significant improvement relative to earlier sensors and competitors.

SR15 first class pyranometer with tube levelling mount

Use as sunshine duration sensor

WMO has approved the “pyranometric method” to calculate sunshine duration from pyranometer
measurements in WMO-No. 8, Guide to Meteorological Instruments and Methods of
Observation. This implies that SR15 may be used, in combination with appropriate software,
to estimate sunshine duration. This is much more cost-effective than using a dedicated sunshine
duration sensor. Ask for our application note.

Suggested use

  • PV system performance monitoring
  • general solar resource monitoring
  • indoor simulated solar testing
  • meteorological networks

Frequently asked questions

How does a pyranometer work?

A pyranometer measures the solar radiation received by a plane surface from a 180 ° field of view angle. This quantity, expressed in W/m², is called “hemispherical” solar radiation. The solar radiation spectrum extends roughly from 285 to 3000 x 10⁻⁹ m. By definition a pyranometer should cover that spectral range with a spectral selectivity that is as “flat” as possible.

In an irradiance measurement by definition the response to “beam” radiation varies with the cosine of the angle of incidence; i.e. it should have full response when the solar radiation hits the sensor perpendicularly (normal to the surface, sun at zenith, 0 ° angle of incidence), zero response when the sun is at the horizon (90 ° angle of incidence, 90 ° zenith angle), and 50 % of full response at 60 ° angle of incidence. A pyranometer should have a so-called “directional response” (older documents mention “cosine response”) that is as close as possible to the ideal cosine characteristic.

In order to attain the proper directional and spectral characteristics, a pyranometer's main components are:

•    a thermal sensor with black coating. It has a flat spectrum covering the 200 to 50000 x 10⁻⁹ m range, and has a near-perfect directional response. The coating absorbs all solar radiation and, at the moment of absorption, converts it to heat. The heat flows through the sensor to the sensor body. The thermopile sensor generates a voltage output signal that is proportional to the solar irradiance.

•    a glass dome. This dome limits the spectral range from 285 to 3000 x 10⁻⁹ m (cutting off the part above 3000 x 10⁻⁹ m), while preserving the 180 ° field of view angle. Another function of the dome is that it shields the thermopile sensor from the environment (convection, rain).

•    a second (inner) glass dome: For secondary standard and first class pyranometers, two domes are used, and not one single dome. This construction provides an additional "radiation shield", resulting in a better thermal equilibrium between the sensor and inner dome, compared to using a single dome. The effect of having a second dome is a strong reduction of instrument offsets.

•    a heater: in order to reduce the effect of dew deposition and frost on the outer dome surface, most advanced pyranometers have a built-in heater. The heater is coupled to the sensor body. Heating a pyranometer can generate additional irradiance offset signals, therefore it is recommended to activate the heater only during night-time. Combining a heater with external ventilation makes these heating offsets very low.

Why use a pyranometer?

There are good reasons why pyranometers are the standard for solar radiation measurement in outdoor PV system performance monitoring. 

The purpose of outdoor PV testing is to compare the available resource to system output and thus to determine efficiency. The efficiency estimate serves as an indication of overall performance and stability. It also serves as a reference for remote diagnostics and need for servicing.

The irradiance measurement for outdoor PV performance monitoring is usually carried out with pyranometers. Some standards suggest using PV reference cells. Reference cells are (with some minor exceptions) unsuitable for proof in bankability and in proof of PV system efficiency. Pyranometers are and will remain the standard for outdoor solar energy monitoring.

From a fundamental point of view:

  • Pyranometers measure truly available solar irradiance (so the amount of available resource). This is the parameter you need to have for a true efficiency calculation.
  • Reference cells measure only that part of solar radiation that can be used by cells of identical material and identical packaging (flat window), so the yield of a certain PV cell type. This is not a measurement that can be used in an efficiency calculation and in fact leads to several percentage points error in efficiency estimates.

The International Energy Agency (IEA) and ASTM standards for PV monitoring recommend pyranometers for outdoor PV monitoring. PV reference cells do not meet IEC 61724-1 class A requirements for irradiance measurement uncertainty: their directional response makes them systematically overestimate daily radiant exposure in J/m2 (or W·hr/m2 ) by more than 2 %, larger on hourly basis. 

How do I choose a pyranometer?

Choosing the right pyranometer for your application is not an easy task. We can offer assistance. But first, you should ask yourself the following questions:

  • are there standards for my application?
  • what level of accuracy do I need?
  • what will be the instrument maintenance level?
  • what are the interfacing possibilities?

When discussing with Hukseflux, our recommendation for the best suited pyranometer will be based on:

  • recommended pyranometer class
  • recommended maintenance level
  • estimate of the measurement accuracy
  • recommended calibration policy
  • recommended interface

Pyranometers can be manufactured to different specifications and with different levels of verification and characterisation during production. The ISO 9060 - 1990 standard, “Solar energy - specification and classification of instruments for measuring hemispherical solar and direct solar radiation”, distinguishes between 3 classes; secondary standard (highest accuracy), first class (second highest accuracy) and second class (third highest accuracy). From second class to first class and from first class to secondary standard, the achievable accuracy improves by a factor 2.

The ISO 9060 - 1990 standard is up for revision. The new 2018 version of the standard will be slightly different from the 1990 version. The new version of ISO 9060 includes three instrument accuracy classes A, B and C, and a special extension of every class “Spectrally Flat”, which is recommended for Plane of Array (POA), albedo, and reflected solar measurements.

Our pyranometer selection guide offers practical guidelines for choosing a pyranometer. The application of pyranometers in PV system performance monitoring according to IEC 61724-1 is highlighted as an example. Sensors specific for diffuse radiation and meteorological networks are also addressed in this selection guide.

What is the difference between a pyrheliometer and a pyranometer?

A pyranometer measures hemispherical solar radiation. When measuring in the horizontal plane this is called Global Horizontal Irradiance (GHI). When measuring in “plane of array”, next to PV panels, this is called plane of array POA irradiance.

A pyrheliometer is used to measure Direct Normal Irradiance (DNI). DNI is defined as the solar radiant flux collected by a plane unit surface normal to the axis pointing towards the centre of the sun, within an optical angular aperture. DNI is composed of the solar irradiance within the extent of the solar disk (half-angle 0.266 ° ± 1.7 %) plus some circumsolar radiation.

SR15-D2A2 pyranometer
SR15 first class pyranometer
  • best measurement accuracy in first class
  • improved response time
  • with SR15-D1’s on-board heater: compliant in its standard configuration with IEC 61724-1 Class B
  • on-board calibration history
Would you like a personalised quote?

or contact us: info@hukseflux.com